KTM 1290

ACCESSORIES for your KTM 1290 R, GT, SE

Evotech nut set RED (6 pcs.) M10x1,25 chainring carrier KTM 1290 SDR / GT
M10x1,25 Evotech nut set RED (6 pcs.) chainring carrier
Aluminium nut set M10x1.25 ( Ergal 7075 T 6 - high strength)
in RED anodised for original chainring carrier or the chainring carrier shown on the other photos.
Tightening torque 45 Nm
30,00 EUR
incl. 19% tax excl. Shipping costs
Evotech nut set ORANGE (6 pcs.) M10x1,25 chainring carrier KTM 1290 SDR / GT
M10x1,25 Evotech nut set ORANGE (6 pcs.) chainring carrier KTM 1290 SDR / GT
Aluminium nut set M10x1.25 ( Ergal 7075 T 6 - high strength)
in ORANGE anodised for original chainring carrier or the chainring carrier shown on the other photos.
Tightening torque 35 Nm  with screw lock
30,00 EUR
incl. 19% tax excl. Shipping costs
Evotech nut set ORANGE (6 pcs.) M8x1,25 chainring KTM 1290 SDR / GT
M8x1,25 Evotech nut set ORANGE (6 pcs.) chainring
Aluminium nut set M8x1.25 ( Ergal 7075 T 6 - high strength)
in ORANGE anodised for the chainring.
Tightening torque 35 Nm with threadlocker
30,00 EUR
incl. 19% tax excl. Shipping costs
Evotech nut set BLACK (6 pcs.) M8x1,25 chainring KTM 1290 SDR / GT
M8x1,25 Evotech nut set BLACK (6 pcs.) chainring
Aluminium nut set M8x1.25 ( Ergal 7075 T 6 - high strength)
in BLACK anodised for the chainring.
Tightening torque 35 Nm with threadlocker
30,00 EUR
incl. 19% tax excl. Shipping costs
Brake lining Brembo SA Sinter 07BB2065
-27%
Brake lining Brembo Sinter 07BB2065 - rear wheel
original equipment flooring
Type 50, sintered metal
Design: Brake lining (disc brake)
Brake pad: Sintered metal OEM
width: 50,8 mm
height: 53,7 mm
thickness: 7,4 mm
With ABE
Suitable for the following motorcycles:
FAHRZEUGLISTE
 
RRP 40,00 EUR
Only 29,00 EUR
incl. 19% tax excl. Shipping costs
Hook spanner Chain tensioner Single-arm swingarm made of STAINLESS STEEL
STAINLESS STEEL Hook spanner Chain tensioner Single-arm swingarm
Tired of getting out the tool kit and putting the tools together every time you want to tighten your chain?
Then this is the right tool for you. Made of 4 mm STAINLESS STEEL with a hole for hanging on the tool wall.
Total length 40 cm
With EVOTECHPARTS engraving - Made in Germany
25,00 EUR
incl. 19% tax excl. Shipping costs
Oil lock screw - BLACK - KTM 1290 SDR / GT / LC8 engine
Oil lock screw - BLACK - KTM 1290 SDR / GT / LC8 engine / 790 / 890 Duke
Oil lock screw - BLACK - KTM 1290 SDR / GT / LC8 engine / 790 / 890 Duke
including sheet metal for receiving the safety wire. The rubber seal from the old lock can be reused....... YOUTUBE Video
25,00 EUR
incl. 19% tax excl. Shipping costs
GALFER brake pad set (2 pcs.) FD373 set G1370, sintered metal road.
TOP
-31%
GALFER brake pad set (2 pcs.) FD373 set G1370, sintered metal road.
GALFER brake pad set (2 pcs.) FD373 set G1370, sintered metal road.
In the opinion of the boss, who tested them on the 1290 Superduke, they are equivalent to the standard pads.
Design: Brake pad (disc brake)
Brake pad: Sintered metal
Width: 102.0 mm
Height: 41.9 mm
Thickness: 7.5 mm
Approval: ECE R90
Material: Steel
Colour: Brown

Suitable for the following MOTORCYCLES
RRP 35,00 EUR
Only 24,00 EUR
incl. 19% tax excl. Shipping costs
Ersatz Crash Protektor Evotech
Crash protector replacement 60 x 70 mm- Evotech Performance
REPLACEMENT CRASH PROTECTOR  EVOTECH PERFORMANCE - 1 Pieces
60 mm x 70 mm
If you would like the same product with an additional camera mount, please see HERE
23,00 EUR
incl. 19% tax excl. Shipping costs
Oil lock screw - ORANGE - KTM 1290 SDR / GT / LC8 engin
-15%
Oil lock screw - ORANGE - KTM 1290 SDR / GT / LC8 engine / 790 / 890 Duke
Oil lock screw - ORANGE - KTM 1290 SDR / GT / LC8 engine / 790 / 890 Duke
including sheet metal for receiving the safety wire.
The colour of the anodisation may change slightly when exposed to heat. This is not a reason for complaint, as it is unavoidable.
The rubber seal from the old lock can be reused....... YOUTUBE Video
RRP 25,00 EUR
Only 21,25 EUR
incl. 19% tax excl. Shipping costs
KTM 1290 hexagon nut M20 x 1,5 for front sprocket
KTM 1290 hexagon nut M20 x 1,5 for front sprocket
KTM 1290 hexagon nut M20 x 1,5 for front sprocket - wrench size 32mm - Made in DE
Assembly tip: Tightening torque: 100 Nm and secured with Loctite ® 243
Scope of delivery: 1 piece
20,00 EUR
incl. 19% tax excl. Shipping costs
Chain lubricant helper from Evotech Performance
TOP
Chain lubricant helper RED from Evotech Performance
Chain Lube Helper from Evotech Performance
Watch the video first. Then you'll see exactly what a great accessory it is: INSTALLATION

The Evotech Performance Chain Lube Applicator is easy to use
Flexible and strong rubber polyurethane ensures easy fitting
Internal paddle nozzles ensure the lubricant hits the motorbike chain in the preferred position
Clear silicone tube allows you to match the applicator outlet to your chosen lubricant
Stainless steel clip holds the silicone tube securely in place
Designed and manufactured by Evotech Performance in the UK
20,00 EUR
incl. 19% tax excl. Shipping costs
Chain lubricant helper from Evotech Performance
Chain lubricant helper ORNAGE from Evotech Performance
Chain Lube Helper from Evotech Performance
Watch the video first. Then you'll see exactly what a great accessory it is: INSTALLATION

The Evotech Performance Chain Lube Applicator is easy to use
Flexible and strong rubber polyurethane ensures easy fitting
Internal paddle nozzles ensure the lubricant hits the motorbike chain in the preferred position
Clear silicone tube allows you to match the applicator outlet to your chosen lubricant
Stainless steel clip holds the silicone tube securely in place
Designed and manufactured by Evotech Performance in the UK
20,00 EUR
incl. 19% tax excl. Shipping costs
Air filter HIFLO HFA-6301 for KTM 1290 SuperDuke / R / GT / Adventure
-10%
Air filter HIFLO HFA-6301 for KTM 1290 SuperDuke / R / GT / Adventure
Air filter HIFLO HFA-6301 for KTM 1290 SuperDuke / R / GT / Adventure
RRP 20,00 EUR
Only 18,00 EUR
incl. 19% tax excl. Shipping costs
41 mm socket wrench / socket with 3/4 inch (20.0 mm) square socket Connection
41 mm socket wrench / socket with 3/4 inch (20.0 mm) square socket Connection
41 mm socket with 12 inside edges - suitable for the rear wheel of the KTM 1290 on the left side. 
.. for hand-operated socket wrench inserts
.. CV steel
.. 20.0 mm (3/4") internal square
.. DIN 3123 / ISO 3316
 
18,00 EUR
incl. 19% tax excl. Shipping costs
Spare spindle head for Evotech Performance axle protectors
Spare spindle head for Evotech Performance axle protectors - small
Evotech Performance's extensive range of axle protectors is designed to give your machine the best possible protection.
Here you can find a part of them as spare part after a fall.
When it comes to safety, sometimes the smallest parts make the biggest difference.
Evotech Performance's extensive range of axle protectors is designed to give your machine the best possible protection.
Here is a part of it as a replacement part after a fall.
When it comes to safety, sometimes the smallest parts make the biggest difference.
Diameter: 60mm
Total height: 33mm
Inner diameter: 37/20 mm
Weight: 115 gram
1 piece is supplied.
Suitable for this MODEL among others
18,00 EUR
incl. 19% tax excl. Shipping costs
Formring clutch cover KTM LC8 1290ccm SuperDuke or GT
clutch cover Formring KTM LC8 KTM LC8 1290 / 1390 ccm
Formring clutch cover KTM LC8 KTM LC8 1290 / 1390 ccm
Sealing ring for the original or transparent clutch cover from Evotech SRL
The sealing ring cannot be inserted, but must be pushed in piece by piece, so to speak.
Otherwise it will be too long when you put it in.
 
17,90 EUR
incl. 19% tax excl. Shipping costs
KTM 1290 / Ducati Streetfighter / Panigale hook spanner galvanised steel chain tensioner
TOP
-20%
steel Hook spanner galvanised chain tensioner
Tired of getting out the tool kit and putting the tools together every time you want to tighten your chain?
Then this is the right tool for you. Made of 4 mm galvanised steel with a hole for hanging on the tool wall.
Total length 40 cm
With EVOTECHPARTS engraving - Made in Germany
RRP 22,00 EUR
Only 17,50 EUR
incl. 19% tax excl. Shipping costs
evotech-led-plate illumination
EVOTECH LED license plate light with 4 mm threaded bolt and 11 mm length
EVOTECH LED license plate light with 4 mm threaded bolt and 11 mm length 
Cable length 30 cm
16,00 EUR
incl. 19% tax excl. Shipping costs
Reinforced number plate made of DIBOND® material 180 x 200 mm
Reinforced number plate (D) 180 x 200 mm made of DIBOND® material

Are you looking for a stable and visually clean solution for mounting your number plate?
We offer a 3 mm thick, 150 gram light DIBOND® plate with perfectly rounded, milled corners.
This is identical to the curves of the number plate.
The plate is matt black on one side and glossy black on the other.
For our customers from SWITZERLAND or LICHTENSTEIN we also have the right size in stock: 140 x 180 mm plate
For our customers from Austria we can recommend this plate: 210 x 170 mm

The plate is supplied without holes.
We used 5 mm countersunk screws for mounting on a KTM Super Duke R 1.0.

The holes on the plate were countersunk with a 5.5 mm drill bit and then with a countersunk drill bit according to the screw.
It is best to use a pillar drill with a depth stop for this.
To secure the M5 cap nut we use Loctite 243.
The reflector with the angle bracket is already included with most EVOTECH PERFORMANCE number plate holders. If not, you can get it HERE.
Alternatively, we also offer a higher-quality reflector kit: REFLEKTORKIT
13,00 EUR
incl. 19% tax excl. Shipping costs
Aluminium screws M5 x 30 for the tank cap KTM 1290 made of Ergal 7075 by Evotech Italy
6 Aluminium screws M5 x 30 for the tank cap KTM 1290 made of Ergal 7075 by Evotech Italy
Aluminium screws M5 x 30 for the tank cap KTM 1290 made of Ergal 7075 by Evotech Italy
Tightening torque: 5 NM
Also fits Ducati Multistrada 1200/1260 and Hypermotard 950
13,00 EUR
incl. 19% tax excl. Shipping costs
Charging cable eyelet cable M6 / M8 with cap, SAE connection, 15 A fuse, length 50 cm
-13%
Charging cable eyelet cable M6 / M8 with cap, SAE connection, 15 A fuse, length 50 cm
TECMATE accessories
Charging cable to charge the motorbike quickly and easily. The eyelets can be mounted on an M6 or M8 screw on the battery. This means you don't need to remove the battery cover every time.
For chargers OptiMATE 1, OptiMATE 2, OptiMATE 3, OptiMATE 4, OptiMATE 5, OptiMATE 6, OptiMATE 7, OptiMATE DC-DC, OptiMATE Lithium, Accu Mate, Accu Gard.
Eyelet cable M6/M8 with cap, SAE connection, 15 A fuse, length 50cm, retail packaging.
Ideal if you have several motorbikes or other vehicles but only one charger.
RRP 15,00 EUR
Only 13,00 EUR
incl. 19% tax excl. Shipping costs
Reinforced number plate made of DIBOND® material 180 x 140 mm
Reinforced number plate (CH+LI) 180 x 140 mm made of DIBOND® material
Are you looking for a stable and visually clean solution for mounting your Swiss or Lichtenstein licence plate?
We offer a 3 mm thick, 100 gram lightweight DIBOND® plate with perfectly rounded, milled corners.
This is identical to the curves of the licence plate.
The plate is matt black on one side and glossy black on the other.
The plate is supplied without holes.
The reflector with the angle bracket is already included with most EVOTECH PERFORMANCE licence plate holders. If not, it is available HERE.
12,00 EUR
incl. 19% tax excl. Shipping costs
License plate and reflector mounting kit
License plate and reflector mounting kit
Our laws require a reflector to be attached to the motorcycle.
Furthermore, you no longer need to worry about mounting license plates of different sizes on our license plate holders.
This kit also includes a set of license plate adapters suitable for all UK and international license plate sizes.
Contents of the kit:
    1 x reflector (self-adhesive)
    1 x reflector holder
    2 x number adapter
    6 x cable ties
    6 x number plate screws
    6 x number plate nuts
12,00 EUR
incl. 19% tax excl. Shipping costs
1/2 in. (12.5 mm) to 3/4 in. (20.0 mm) magnification piece
Magnification piece 1/2 inch (12.5 mm) to 3/4 inch (20.0 mm)
This adapter or magnification piece is required when the torque tool has a 1/2 inch (12.5 mm) square and the required nut has a 3/4 inch (20.0 mm) square.
for hand-operated socket wrench inserts

. CV steel
. 12.5 mm(1/2") to 20.0 mm(3/4") Outside square
. DIN 3123 / ISO 3316

10,00 EUR
incl. 19% tax excl. Shipping costs
Spare spindle head for Evotech Performance axle protectors
Spare spindle head for Evotech Performance axle protectors
Evotech Performance's extensive range of axle protectors is designed to give your machine the best possible protection.
Here you can find a part of them as spare part after a fall.
When it comes to safety, sometimes the smallest parts make the biggest difference.
Outer diameter: 46.5 mm
Outer diameter at the tip: 36 mm
Height: 26 mm
Bore: 12.4 mm
10,00 EUR
incl. 19% tax excl. Shipping costs
Oil filter HIFLO HF650 for KTM 1290 R / GT / Adventure
Oil filter HIFLO HF650 for KTM 1290 R / GT / Adventure
Replacement oil filter HIFLO HF650 for KTM 1290 R / GT / Adventure. Best quality at a reasonable price. For those who change the oil themselves. Nothing simpler than this
7,00 EUR
incl. 19% tax excl. Shipping costs
Evotech nut BLACK (1 pcs.) M8x1,25 chainring KTM 1290 SDR / GT
M8x1,25 Evotech nut set BLACK (1 pcs.) chainring
Aluminium nut M8x1.25 ( Ergal 7075 T 6 - high strength)
in BLACK anodised for the chainring.
Tightening torque 35 Nm with threadlocker
1 Pieces
6,00 EUR
incl. 19% tax excl. Shipping costs
EVOTECHPARTS Alloy nut M10x1.25 for chainring carrier KTM 1290 SDR / GT
M10x1.25 EP Alloy nut M10x1.25 for chainring carrier
Aluminium nut set M10x1.25 (6026 T 6 - high strength)
in ORANGE anodised for original chainring carrier or the chainring carrier shown in the other photos.
The price is for 1 nut in orange
For the KTM 1290 SDR / GT
(6 pieces are required)
Tightening torque 45 Nm
5,00 EUR
incl. 19% tax excl. Shipping costs
Evotech nut ORANGE (1 pcs.) M8x1,25 chainring KTM 1290 SDR / GT
-20%
M8x1,25 Evotech nut ORANGE (1 pcs.) chainring
Aluminium nut M8x1.25 ( Ergal 7075 T 6 - high strength)
in ORANGE anodised for the chainring.
Tightening torque 35 Nm with threadlocker
RRP 6,00 EUR
Only 4,80 EUR
incl. 19% tax excl. Shipping costs
Locking plate for sprocket KTM 1290
Locking plate for sprocket KTM 1290
Locking plate for sprocket KTM 1290
3,50 EUR
incl. 19% tax excl. Shipping costs
Stainless steel screw and nut set for licence plate
Stainless steel screw and nut set for licence plate
The set (12 parts) consists of:
2 x M6x16 countersunk screw
2 x M5x10 countersunk screw
2 x M5x12 pan-head screw
2 x M6 hexagon nut
4 x M5 hexagon nut
This gives you a complete screw/nut set if you use our IDENTIFICATION PLATE and the REFLECTOR KIT.
3,00 EUR
incl. 19% tax excl. Shipping costs
Screw set for clutch cover KTM 1290 by Evotech Italy
Screw for clutch cover KTM 1290/1390 by Evotech Italy - ORANGE
1290
Aluminium screws M6 for clutch cover KTM 1290 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the standard clutch cover you need: 1 x 90 mm, 2 x 85 mm, 1 x 30 mm, 1 x 25 mm
For additional assembly of PRO-09-01 you need: 2 x 90 mm, 1 x 85 mm, 2 x 30 mm
For the EVOTECH clutch cover you need: 3 x 85 mm, 2 x 25 mm
For additional assembly of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 85 mm, 1 x 90 mm

1390
Aluminium screws M6 for clutch cover KTM 1390 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the EVOTECH clutch cover you need: 3 x 80 mm, 2 x 25 mm
For additional installation of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 80 mm, 1 x 85 mm

Tightening torques: 8 NM
from 2,30 EUR
incl. 19% tax excl. Shipping costs
Screw set for clutch cover KTM 1290 by Evotech Italy
Screw for clutch cover KTM 1290/1390 by Evotech Italy - Black
1290
Aluminium screws M6 for clutch cover KTM 1290 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the standard clutch cover you need: 1 x 90 mm, 2 x 85 mm, 1 x 30 mm, 1 x 25 mm
For additional assembly of PRO-09-01 you need: 2 x 90 mm, 1 x 85 mm, 2 x 30 mm
For the EVOTECH clutch cover you need: 3 x 85 mm, 2 x 25 mm
For additional assembly of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 85 mm, 1 x 90 mm

1390
Aluminium screws M6 for clutch cover KTM 1390 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the EVOTECH clutch cover you need: 3 x 80 mm, 2 x 25 mm
For additional installation of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 80 mm, 1 x 85 mm

Tightening torques: 8 NM
from 2,30 EUR
incl. 19% tax excl. Shipping costs
76 to 109 (from a total of 109)