Screw for clutch cover KTM 1290/1390 by Evotech Italy - ORANGE
1290
Aluminium screws M6 for clutch cover KTM 1290 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the standard clutch cover you need: 1 x 90 mm, 2 x 85 mm, 1 x 30 mm, 1 x 25 mm
For additional assembly of PRO-09-01 you need: 2 x 90 mm, 1 x 85 mm, 2 x 30 mm
For the EVOTECH clutch cover you need: 3 x 85 mm, 2 x 25 mm
For additional assembly of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 85 mm, 1 x 90 mm
1390
Aluminium screws M6 for clutch cover KTM 1390 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the EVOTECH clutch cover you need: 3 x 80 mm, 2 x 25 mm
For additional installation of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 80 mm, 1 x 85 mm
Tightening torques: 8 NM
Aluminium screws M6 for clutch cover KTM 1290 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the standard clutch cover you need: 1 x 90 mm, 2 x 85 mm, 1 x 30 mm, 1 x 25 mm
For additional assembly of PRO-09-01 you need: 2 x 90 mm, 1 x 85 mm, 2 x 30 mm
For the EVOTECH clutch cover you need: 3 x 85 mm, 2 x 25 mm
For additional assembly of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 85 mm, 1 x 90 mm
1390
Aluminium screws M6 for clutch cover KTM 1390 made of Ergal 7075 from Evotech Italy
You will need the following range of screws:
For the EVOTECH clutch cover you need: 3 x 80 mm, 2 x 25 mm
For additional installation of PRO-09-01 you need: 1 x 25 mm, 1 x 30 mm, 2 x 80 mm, 1 x 85 mm
Tightening torques: 8 NM
- Manufacturer:
SEVENTYONE S.R.L.
Zona Industriale Palù, 6G - 38055 Grigno (TN)
Phone: +39 0461 780184
info@evotech-rc.it
General safety instructions for the product:
We recommend that you always consult a specialist workshop when fitting our products or have this work carried out by a specialist. If you fit it yourself, please make sure that your motorbike is secure and that the product is only intended for your motorbike. The models for which the product is tested and intended can be found with each item.
To avoid damage to your motorbike during installation, we recommend covering all important/sensitive parts. Please understand that we cannot accept any liability for consequential damage caused by improper installation.
When fitting, use threadlocker if possible and observe the torque specifications. The fixing screws on the licence plate holder in particular should be secured with threadlocker. Loss of the licence plate holder due to lost screws can cause unpleasant damage.
General torque specifications can be found HERE
The legally required licence plate angle of 30 degrees can be set on the Italian licence plate holders
Information for our Austrian customers specifically for the type approval and registration of licence plate holders can be found HERE
Unfortunately there are no reviews yet. Be the first who rates this product.
You must be logged in to submit a review. Login