.jpg "Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Preview: Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Preview: Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Preview: Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Reinforced number plate made of DIBOND® material 180 x 200 mm")
.jpg "Reinforced number plate made of DIBOND® material 180 x 200 mm")
Are you looking for a stable and visually clean solution for mounting your number plate?
We offer a 3 mm thick, 150 gram light DIBOND® plate with perfectly rounded, milled corners.
This is identical to the curves of the number plate.
The plate is matt black on one side and glossy black on the other.
For our customers from SWITZERLAND or LICHTENSTEIN we also have the right size in stock: 140 x 180 mm plate
For our customers from Austria we can recommend this plate: 210 x 170 mm
The plate is supplied without holes.
We used 5 mm countersunk screws for mounting on a KTM Super Duke R 1.0.
The holes on the plate were countersunk with a 5.5 mm drill bit and then with a countersunk drill bit according to the screw.
It is best to use a pillar drill with a depth stop for this.
To secure the M5 cap nut we use Loctite 243.
The reflector with the angle bracket is already included with most EVOTECH PERFORMANCE number plate holders. If not, you can get it HERE.
Alternatively, we also offer a higher-quality reflector kit: REFLEKTORKIT
We offer a 3 mm thick, 150 gram light DIBOND® plate with perfectly rounded, milled corners.
This is identical to the curves of the number plate.
The plate is matt black on one side and glossy black on the other.
For our customers from SWITZERLAND or LICHTENSTEIN we also have the right size in stock: 140 x 180 mm plate
For our customers from Austria we can recommend this plate: 210 x 170 mm
The plate is supplied without holes.
We used 5 mm countersunk screws for mounting on a KTM Super Duke R 1.0.
The holes on the plate were countersunk with a 5.5 mm drill bit and then with a countersunk drill bit according to the screw.
It is best to use a pillar drill with a depth stop for this.
To secure the M5 cap nut we use Loctite 243.
The reflector with the angle bracket is already included with most EVOTECH PERFORMANCE number plate holders. If not, you can get it HERE.
Alternatively, we also offer a higher-quality reflector kit: REFLEKTORKIT
- Manufacturer information/responsible person:
EVOTECH GERMANY
Lothar Westphal
Eichendorffstr. 9
78239 Rielasingen, Germany
Tel. 07731 8229019
mail @ evotechparts.com
General safety information about the product:
We recommend that you always consult a specialist workshop or have the work carried out by a specialist when installing or using our products. If you install it yourself, please ensure that your motorcycle is secure and that the product is only intended for your motorcycle. For this purpose, each item lists the models for which the product has been tested and is intended.
To avoid damage to your motorcycle during installation, we recommend covering all important/sensitive parts. Please understand that we cannot accept any liability for consequential damage caused by improper installation.
When installing, use screw lock if possible and observe the torque specifications.
General torque specifications can be found HERE
Unfortunately there are no reviews yet. Be the first who rates this product.
You must be logged in to submit a review. Login
Customers who bought this product bought also the following products:
This product was added to our catalog on Wednesday, June 30, 2021.