Rear axle nut M48x1.5 RED Duraluminium Evotech Italien
Rear axle nut M48x1.5 RED Duraluminium Evotech Italien
Rear axle nut M48x1.5 RED Duraluminium Evotech Italien

Rear axle nut M48x1.5 RED Duraluminium Evotech Italien

Product No.:
TB-014/CR-A2
Shipping time:
soon available again soon available again (abroad may vary)
Weight:
0.05 kg per piece
61,10 Dollar

incl. 19% tax excl. Shipping costs

Add to wish list
Ask about product
EU legal guarantee notice
Description
Very high quality duraluminium nut (7075T6) for the rear wheel
Machined on CNC-controlled machines, a great design and a refined look can be realised.
The 6 bulges and the 6 frontal holes reduce weight compared to the original without compromising stability. The tightening torque remains unchanged. The mounting is done with a standard ring spanner or nut.
Supplied with: 1 x rear axle nut with 55 mm spanner size.
Products Safety/TÜV
Manufacturer:
SEVENTYONE S.R.L.
Zona Industriale Palù, 6G - 38055 Grigno (TN)
Phone: +39 0461 780184
info@evotech-rc.it

General safety instructions for the product:
We recommend that you always consult a specialist workshop when fitting our products or have this work carried out by a specialist. If you fit it yourself, please make sure that your motorbike is secure and that the product is only intended for your motorbike. The models for which the product is tested and intended can be found with each item.
To avoid damage to your motorbike during installation, we recommend covering all important/sensitive parts. Please understand that we cannot accept any liability for consequential damage caused by improper installation.
When fitting, use threadlocker if possible and observe the torque specifications. The fixing screws on the licence plate holder in particular should be secured with threadlocker. Loss of the licence plate holder due to lost screws can cause unpleasant damage.
General torque specifications can be found HERE

The legally required licence plate angle of 30 degrees can be set on the Italian licence plate holders

Information for our Austrian customers specifically for the type approval and registration of licence plate holders can be found HERE
 
Customer reviews

Unfortunately there are no reviews yet. Be the first who rates this product.

Customers who bought this product bought also the following products:

evotech-led-plate illumination
EVOTECH LED license plate light with 4 mm...
EVOTECH LED license plate light with 4 mm threaded bolt and 11 mm length 
Cable length 30 cm
20,80 Dollar
Reinforced number plate made of DIBOND® material 180 x 200 mm
Reinforced number plate (D) 180 x 200 mm...

Are you looking for a stable and visually clean solution for mounting your number plate?
We offer a 3 mm thick, 150 gram light DIBOND® plate with perfectly rounded, milled corners.
This is identical to the curves of the number plate.
The plate is matt black on one side and glossy black on the other.
For our customers from SWITZERLAND or LICHTENSTEIN we also have the right size in stock: 140 x 180 mm plate
For our customers from Austria we can recommend this plate: 210 x 170 mm

The plate is supplied without holes.
We used 5 mm countersunk screws for mounting on a KTM Super Duke R 1.0.

The holes on the plate were countersunk with a 5.5 mm drill bit and then with a countersunk drill bit according to the screw.
It is best to use a pillar drill with a depth stop for this.
To secure the M5 cap nut we use Loctite 243.
The reflector with the angle bracket is already included with most EVOTECH PERFORMANCE number plate holders. If not, you can get it HERE.
Alternatively, we also offer a higher-quality reflector kit: REFLEKTORKIT
16,90 Dollar
This product was added to our catalog on Tuesday, April 18, 2023.